lee@ricewind.comTel+86 17621197907Serving 50+ countries
RICEWIND

Vertiv / Power management

Liebert GXE2 Equipment information & support

Vertiv Liebert GXE2 is an industrial-grade, high-reliability solution engineered for mission-critical telecom sites, data centers, and power applications.

Equipment information

Brand
Vertiv
Equipment model
Liebert GXE2
Equipment type
Power management
Controller / software version
Confirm against the installed equipment
View full product specifications
Vertiv Liebert GXE2 pure white studio product shot

Information below comes from the current product catalogue. Confirm the controller, software version and configuration of the installed equipment separately.

Topology
Online Double Conversion High Frequency UPS
Output Power Factor
0.9 ~ 1.0 High Unity Power Factor
ECO Mode Efficiency
Up to 98% in ECO Mode (≥95% Online Mode)
Battery Voltage
Flexible 192V - 240V DC Adjustable Bus
Transfer Time
0 ms (Mains to Inverter / Zero Phase Break)
Communication Slots
Dry Contacts, USB, RS232, Optional SNMP Card

Alarms & troubleshooting

AC_FAIL (AC Mains Input Failure/Out of Range)
RUN LED (Green) OFF; ALM LED (Yellow) or FAULT LED (Red) Solid ON
Utility blackout, branch breaker trip, AC phase voltage below 80VAC or above 300VAC cutoff, or loose chassis rear connector pin
1. Measure AC input terminal voltage to verify it within normal envelope; 2. Check and reset the branch miniature circuit breaker (MCB); 3. Unseat and inspect rear connector pins, then reseat firmly; 4. If AC supply is stable and reseating fails, replace module.
DC_VOLT_HIGH (DC Output Overvoltage Hardware Lockout)
FAULT LED (Red) Solid ON, module output completely gated and locked off
Internal optocoupler feedback loop failure, strong EMI on current-share bus, or hardware overvoltage comparator trip (>59.5VDC)
1. Disconnect AC input, wait 2 minutes for capacitor discharge, then re-energize; 2. If overvoltage trips immediately, internal regulation circuit is defective—replace module; 3. Verify float/boost voltage calibration in the central controller.
FAN_FAIL / OVER_TEMP (Cooling Fan Stall or Internal Thermal Runaway)
ALM LED (Yellow) Blinking continuously; cooling fan halted or abnormal acoustic noise
Airflow channel heavily clogged by dust/debris, seized fan bearing, ambient temperature exceeding +55°C, or disconnected fan tachometer signal cable
1. Extract module and clean air filters and heatsink fins; 2. Manually spin fan blades to ensure smooth rotation without friction; 3. Verify room air conditioning system; 4. If fan remains halted after cleaning, replace fan assembly or unit.
COMM_LOST (Telemetry / CAN Bus Communication Loss)
Controller screen displays 'Module Lost/Offline', module operates in autonomous fallback float mode
Oxidized gold fingers on backplane interface, improper CAN termination resistor, duplicated node ID address, or controller lockup
1. Remove module and clean rear gold-finger contacts with isopropyl alcohol; 2. Run 'Rescan Nodes' on controller GUI; 3. Verify the 120-ohm CAN termination jumper; 4. Soft reboot the central supervision unit.
SHORT_CIRCUIT / I_LIMIT (DC Short Circuit or Current Foldback Limit)
ALM LED (Yellow) Solid ON, output voltage clamped down below safety foldback threshold
Downstream DC branch cabling short-circuit, internal battery cell short, or severe inrush load current exceeding 120% rating
1. Sequentially switch off downstream DC distribution breakers to pinpoint faulted branch; 2. Disconnect battery breaker to test open-circuit terminal voltage; 3. Once external short is isolated, module recovers regulated output automatically.

Access Complete Maintenance & Full Alarm Troubleshooting Manual

This page lists high-frequency critical alarm codes commonly encountered in field maintenance. Comprehensive manufacturer troubleshooting matrices, board-level repair guides, detailed electrical schematics, and firmware commissioning manuals are delivered alongside equipment upon formal project procurement, accompanied by dedicated FAE technical support.

Contact Account Manager for Full Manual

Share on-site information

  1. 01

    Identify the exact model

    Record the nameplate, system model and controller or module model.

  2. 02

    Keep the alarm details

    Record the full alarm text, indicator colour, timing and whether it persists.

  3. 03

    Describe recent changes

    Note recent replacements, software updates or configuration changes.

Record information visible in the existing interface. Electrical measurements, disassembly and replacement should follow the applicable manufacturer's manual and be performed by qualified personnel.

Your model and these details will be added to the enquiry form for you to review before sending.

Related technical articles

Browse the technical guides or send a question about this model.

View all articles

Need a replacement module or supporting equipment?

Confirm the full model, system configuration and compatibility requirements before enquiring about suitable products.

Ask about suitable products

Have a model and an on-site issue?

Share the exact model, alarm text and observed symptoms to help identify relevant information and compatibility requirements.

Request technical support